This is the digital manual for the Red Series Smart Light Strip Controller Kit.

Please click on any of the sections in the Table of Contents to get started. We recommend working your way down as it follows an intentional flow that is user friendly and hub/gateway specific. As always, any questions, please see the Additional Resources links section or submit a ticket, we’re happy to help.
​

When you are ready to include/pair your Red Series Light Strip Controller Kit (LZW45), please start the inclusion process on your Z-Wave enabled hub. Once your hub has started the inclusion process, quickly tap three (3) times on the configuration/favorites button (A) and the light strip will start to pulse blue.
​

If your light strip controller includes successfully, the light strip will blink Green temporarily and then go back to Blue. If the controller does not include successfully, the light strip will blink Red temporarily and then go back to Blue.

Please refer to the above diagram to get to know your light strip controller.

A. Config Button (and Scene Control*): This button can be used for various functions as shown in the table to the right. It can also be used to trigger a Z-Wave scene. The scene is triggered when this button is pressed one time.

B. Level Up Button (and Scene Control*): This button can be used to increase the level on your lightstrip. Press (hold) up to increase brightness. It can also be used to trigger a Z-Wave scene. It supports up to 7 scenes (Tap x, 2x, 3x, 4x, 5x, Hold, Release).

C. Level Down Button (and Scene Control*): This button can be used to decrease the level on your lightstrip. Press (hold) down to decrease brightness. It can also be used to trigger a Z-Wave scene. It supports up to 7 scenes (Tap x, 2x, 3x, 4x, 5x, Hold, Release).

D. Digital Display: The display is used for several different functions during the operation of your lightstrips. In local config mode it will display the configuration parameter you are editing and the value. In normal operation it will show the level that the lightstrips are at. When your controller is running an effect (flashing, pulsing etc.), the display will flash alternating symbols. Note: there is a 5 second time out for the display. Five seconds after it has displayed the current status, it will turn off as to not bother the user.

E. DC Power Connector: This is where you plug-in the included 2V power supply. The rating of the power supply is 2V DC 2.0A.

* Hub must support these features.

The Inovelli light strip controller kit can be used on various hub platforms such as: SmartThings, Home Assistant - Z-WaveJS, Home Assistant - Z-WaveJSUI, Hubitat, and HomeSeer. If you'd like specific instructions on how to setup this controller on your hub's platform, please click the links below to be taken to them:

If you don't see your hub listed above, please go to the, "Quick Setup & Inclusion" section for generic instructions.

These light strip controllers are packed with a ton of amazing features, which include scene control (multi-tap), animated notifications, energy monitoring, and 20 different parameters to customize your light strip.

To see the list of parameters on this controller, please click on the following link: Red Series Light Strip Controller Kit Parameters

The Quick Strip Effects are the same as our smart switch Animated Notifications. Some common use examples are:

To see examples of the various notifications, check out our Toolbox located here and select the On/Off + Dimmer Switch (VZW31-SN) under, "Z-Wave" and click the dropdown where it says, "Effect": https://inovelliusa.github.io/inovelli-switch-toolbox/

Setup instructions are different for each hub, so we've created instructions for the following hubs:

The Custom Strip Effects are similar our smart switch Animated Notifications, but give you more customization over color/transition, dim level, duration and number of iterations the effect repeats. Some common use examples are:

To see examples of the various notifications, check out our Toolbox located here and select the On/Off + Dimmer Switch (VZW31-SN) under, "Z-Wave" and click the dropdown where it says, "Effect": https://inovelliusa.github.io/inovelli-switch-toolbox/ (NOTE: To get the specific parameter values, please use our LED Strip Toolbox Calculator)

Setup instructions are different for each hub, so we've created instructions for the following hubs:

The Pixel Effects are pre-installed animations that can quickly be turned on. There are 46 to choose from and they are located in the drop-down below:

Setup instructions are different for each hub, so we've created instructions for the following hubs:

Scene control allows you to multi-tap your light strip controller to activate certain scenes. Some common examples are:

Setup instructions are different for each hub, so we've created instructions for the following hubs:

Please see the below sections to learn more about Z-Wave and how it relates to this controller.

The DSK information required for some inclusion methods can be found either on the product (QR Code located on the back at the bottom-left of the controller), or on the back of the box at the bottom left (QR Code located at the bottom right). Please keep this in a safe space or write it down for your records.

Group 1: Lifeline

Members of this group will receive unsolicited messages related to the status of the controller

Group 2: Basic Set

Sends On & Off commands to associated devices

Group 3: Switch Multilevel Set

Sends set level commands to associated devices when up/down buttons are pressed.

Group 4: Switch Multilevel Set

Sends start / stop level change to associated devices

This product can be operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. Each module is designed to act as a repeater, which will re-transmit a radio frequency (RF) signal by routing the signal around obstacles and radio dead spots to ensure that the signal is received at its intended destination. The Inovelli Red Series Light Strip Controller Kit is a security enabled Z-Wave Plus device. A security enabled Z-Wave Plus controller must be used in order to fully utilize the product.

This device is compatible with SmartStart.
​

SmartStart enabled products can be added into a Z-Wave network by scanning the Z-Wave QR Code found on the bottom left corner of the controller, the back of the box or the insert inside the package with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being controller on and in the network vicinity.

To factory reset your device, first, hold the Configuration / Favorites Button (A) for 20 seconds until the light strip turns red and let go. The light strip should blink red a few times indicating it has been factory reset. You may also use a certified Z-Wave controller to remove the device from your network to factory default. Only use these procedures in the event that the primary controller is missing or otherwise inoperable.

Exclusion will reset your device as well and can be done directly from the hub. This is helpful if you’re running into issues with inclusion. To exclude a device, start the exclusion process on your hub and press the Configuration / Favorites Button (A) 3x rapidly. The light strip will start pulsing blue and if successful, it will flash green. If unsuccessful it will flash red.

Name: Light Strip Controller Kit

SKU #: LZW45

Power: 120V AC, 60Hz Signal

(Frequency): 908.42 MHz

Operating Temperature Range: 32-95° F (0-35° C)

Pixel Type: WS2815

Lumens: 1600 (6ft) or 267 lm/foot (lumens will drop after 16ft without additional power source)

Color Range: Full RGB (Red, Green, Blue) + Tunable White

Temperature Range: 2700k to 6500k (Warm to Cold White)

CRI/Ra Value: 80

R9: 0

Wattage: 20W

Range: Up to 100 meters line of sight between the Wireless Controller (HUB) and the closest Z-Wave Repeater.

Certifications: ETL Listed (#5003280), FCC/IC & Z-Wave Plus Certified
​

For indoor use. Specifications subject to change without notice due to continuing product improvement.

If you run into any issues, feel free to reach out to us. We typically answer tickets within 24-48 hours and are staffed by actual smart home owners.
​

All Inovelli products come with a one (1) year warranty (defined as 365 days). This warranty protects you from breakdowns in the material or workmanship under normal use. This warranty is limited in a couple areas. Purchases must be made from Inovelli or an authorized reseller. The product should be used in the manner directed in the instructions. The product must only be used and/or installed in the United States or Canada.
​

For full warranty info, please visit: inov.li/warranty

This is the second project that we have teamed up with the community on to help visualize, develop, and beta test it. Having a group of enthusiastic smart home users to guide this project to completion has been invaluable. They have been a true pleasure to work with and this product would not be nearly what it is without them. Thanks to the beta testers for all their hard work - we couldn’t do it without you!

To see the origin of this project, as well as the journey scan the code or visit: inov.li/cribs

(Keep in mind this may be out of date)