Please use this document as a resource to understand the various parameters on your Blue Series On/Off switch. We try to keep this up-to-date, but as we constantly change our firmware, there may be a mistake. Please reach out if you see anything that needs to be corrected.

Please see the table below for a quick reference guide to the parameters on the Blue Series On/Off switch (VZM30-SN). The table is meant to provide a high level view of all the parameters. For a full explanation of each parameter, please click on the hyperlink in each cell to be taken down the page to the appropriate section.

These are the parameters that the switch has when used without Zigbee Bindings.

These parameters are used when Zigbee Bindings are enabled. Zigbee Bindings are used when you want to control your smart bulbs. Note that your hub and end Zigbee product (e.g., smart bulb, smart switch, etc.) must support them.

Below we'll list out the parameter number, description, range, default value, size, firmware version it was implemented and an example of how to use it.

Switch Type refers to the type of wiring installation your switch is in: Single Pole or 3-Way Aux.

Smart Bulb Mode is a mode that allows your switch to be used with smart bulbs that are wired to the switch (ie: it locks in full power and sends digital signals to the hub to turn on/off/dim the smart bulb rather than cutting power to the bulb).

To program your Blue Series On/Off switch which installation type it's in (ie: Single Pole or 3-Way Aux) you'll want to change Parameter 22 and enter in 0 for Single Pole, or 1 for Multi-Way (3-Way) with an Auxiliary / Add-On switch (which is the default).

Dimming speed refers to how fast or slow the light turns on when you change the dim level either remotely or locally (at the switch) such as from 10-20%, 60-80%, etc.

Ramp rate refers to how fast or slow the light turns on when you either remotely or locally (at the switch) bring the switch from off to on (or on to off).

Default Level - Local refers to the default dim level the switch goes to when turned on at the switch (ie: if you set the default level to 60%, that's the percentage the switch turns on to when you turn it on).

Default Level - Remote refers to the default dim level the switch goes to when turned on remotely via the app (ie: if you set the default level to 60%, that's the percentage the switch turns on to when you turn it on).

Binding Default Level allows you to match the default level parameter (Parameter 13 & 14) when using Zigbee Bindings.

To change the remote dimming speed for dimming up on your Blue Series On/Off Switch, you would select Parameter 1 within your hub and then input a range of 0-126, with each interval equating to 100 milliseconds and the default being 2.5 seconds.

To change the dimming speed at the switch (locally) for dimming up on your Blue Series On/Off Switch, you would select Parameter 2 within your hub and then input a range of 0-127, with each interval equating to 100 milliseconds and the default being that the switch will default to whatever is selected in Parameter 1.

To change the remote dimming speed for dimming down on your Blue Series On/Off Switch, you would select Parameter 5 within your hub and then input a range of 0-126, with each interval equating to 100 milliseconds and the default being that the switch will default to whatever is selected in Parameter 1.

To change the dimming speed at the switch (locally) for dimming down on your Blue Series On/Off Switch, you would select Parameter 6 within your hub and then input a range of 0-127, with each interval equating to 100 milliseconds and the default being that the switch will default to whatever is selected in Parameter 2.

To change the remote ramp rate for how fast your Blue Series On/Off Switch goes from off to on, you would select Parameter 3 within your hub and then input a range of 0-127, with each interval equating to 100 milliseconds and the default being that the switch will default to whatever is selected in Parameter 1.

To change the remote ramp rate for how fast your Blue Series On/Off Switch goes from off to on, you would select Parameter 4 within your hub and then input a range of 0-127, with each interval equating to 100 milliseconds and the default being that the switch will default to whatever is selected in Parameter 3.

To change the ramp rate for how fast your Blue Series On/Off Switch goes from on to off remotely in your app, you would select Parameter 7 within your hub and then input a range of 0-127, with each interval equating to 100 milliseconds and the default being that the switch will default to whatever is selected in Parameter 3.

To change the ramp rate for how fast your Blue Series On/Off Switch goes from on to off locally at the switch, you would select Parameter 8 within your hub and then input a range of 0-127, with each interval equating to 100 milliseconds and the default being that the switch will default to whatever is selected in Parameter 4.

To set the default level your Blue Series On/Off Switch turns on to when you manually press the switch, you would select Parameter 13 within your hub and then input a range of 0-255, where zero (0) equals off, 255 equals the last level the switch was set at, the lower the numeric value equals a lower dim level (1 = ~1%) and the higher the numeric value equals a higher dim level (254 = ~100%) with the default being that the switch will return to the prior state it was in.

To set the default level your Blue Series On/Off Switch turns on to when you turn on your switch remotely (via an app), you would select Parameter 14 within your hub and then input a range of 0-255, where zero (0) equals off, 255 equals the last level the switch was set at, the lower the numeric value equals a lower dim level (1 = ~1%) and the higher the numeric value equals a higher dim level (254 = ~100%) with the default being that the switch will return to the prior state it was in.

If you'd like your Blue Series On/Off switch to easily turn onto 100% via a double-tap on the up (top) paddle, turn on Parameter 53 (if you'd like to set a specific value other than 100%, then also turn on Parameter 55 and set the level). The default is 0, which has this feature turned off.

If you'd like your Blue Series On/Off switch to easily turn down to 1% via a double-tap on the down (bottom) paddle, turn on Parameter 54 (if you'd like to set a specific value other than 1%, then also turn on Parameter 56 and set the level). The default is 0, which has this feature turned off.

If you'd like your Blue Series On/Off switch to easily turn onto a certain dim percentage via a double-tap on the up (top) paddle, turn on Parameter 55 (also remember to turn on Parameter 53 - 2x Up to P55). The lower the numeric value equals a lower dim level (1 = ~1%) and the higher the numeric value equals a higher dim level (254 = ~100%) with the default being 254 (100%).

If you'd like your Blue Series On/Off switch to easily turn down to a certain dim percentage via a double-tap on the down (bottom) paddle, turn on Parameter 56 (also remember to turn on Parameter 54 - 2x Down to P56). The lower the numeric value equals a lower dim level (1 = ~1%) and the higher the numeric value equals a higher dim level (254 = ~100%) with the default being 2 (~1%).

If your Blue Series On/Off Switch is bound to a Zigbee smart bulb and you'd like to set a default level when turned on, change Parameter 125 to 1 (and also set the default level parameters - 13 & 14). By default this parameter is set to 0, which disables this feature.

Invert Switch refers to inverting the switch (where tapping up on the switch will turn the switch off and tapping down on the switch will turn the switch on)

Auto-Off Timer refers to the switch being turned off after a certain amount of time (in seconds).

To invert your Blue Series On/Off Switch (ie: tapping on the up button turns your light off and tapping on the down button turns your light on), you would select Parameter 11 within your hub and then select either 0 to keep it non-inverted or 1 to invert it with the default being that the switch is not inverted (value of 0).

To set an auto-off timer where you can have your Blue Series On/Off Switch turn off after a certain amount of seconds, you would select Parameter 12 within your hub and then input a range of 0-32767, where each interval is a second.

Level After Power Restored refers to the level the switch will return to when power is restored to it (ie: after a power outage).

LED Indicator Timeout changes the amount of time (in seconds) the RGB Bar shows the Dim Level (ie: if you are actively dimming the light, the LED Bar will show you approximately what level the light is at -- the timeout is the time that indicator shows once you let go of the paddle)

To set the behavior that your Blue Series On/Off Switch enacts after a power outage, you would select Parameter 15 within your hub and then input a range of 0-255, where zero (0) equals off, 255 equals the last level the switch was set at, the lower the numeric value equals a lower dim level (1 = ~1%) and the higher the numeric value equals a higher dim level (254 = ~100%) with the default being that the switch will return to the prior state it was in.

To adjust the time that the LED Bar displays the value of what your Blue Series On/Off Switch is at (ie: on/off, dim level), you would select Parameter 17 within your hub and then input a range of 0-11, where zero (0) equals always off, each interval equals one second and 11 equals always on.

Active Power Reports refer to the reporting of the power level change and will result in a new power report being sent in wattage (W).

Periodic Power & Energy Reports refer to the time period between consecutive power and energy reports being sent (in seconds).

Energy Reports refer to the reporting of the energy level change and will result in a new energy report being sent in kilowatt hours (kWh).

To adjust the threshold at which a power report is sent based on a change in Wattage on your Blue Series On/Off Switch, you would select Parameter 18 within your hub and then input a range of 0-32767, where zero disables the reports and each interval equals 0.1 Watt.

To adjust the time period at which consecutive power or energy reports are sent on your Blue Series On/Off Switch, you would select Parameter 19 within your hub and then input a range of 0-32767, where zero disables the reports and each interval equals 1 second.

To adjust the threshold at which an energy report is sent based on a change in kilowatt hours on your Blue Series On/Off Switch, you would select Parameter 20 within your hub and then input a range of 0-32767, where zero disables the reports and each interval equals 0.01 kilowatt hours (kWh).

Please use the chart below to understand what parameters align with what LED on the switch. For a visual example, please visit the Inovelli Toolbox which will show you what the various animations look like (be sure to select, "On\Off + Dimmer Switch (VZM31-SN)" - it has the same animations as the VZM30-SN).

To adjust the color of the bottom LED (LED #1) on the Blue Series On/Off switch when the light (load) is on, find parameter 60 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM31-SN)" - it has the same animations as the VZM30-SN - and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #1 to sync to whatever is set in Parameter 95 (Default of All LED Strip Color - When On).

To adjust the color of the bottom LED (LED #1) on the Blue Series On/Off switch when the light (load) is off, find parameter 61 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM31-SN)" - it has the same animations as the VZM30-SN - and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #1 to sync to whatever is set in Parameter 96 (Default of All LED Strip Color - When Off).

To adjust the bottom LED's brightness (LED #1) on the Blue Series On/Off switch when the light (load) is on, find parameter 62 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #1 to sync to whatever is set in Parameter 97 (Default of All LED Strip Intensity - When On).

To adjust the bottom LED's brightness (LED #1) on the Blue Series On/Off switch when the light (load) is off, find parameter 63 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #1 to sync to whatever is set in Parameter 98 (Default of All LED Strip Intensity - When Off).

To adjust the color of the second from the bottom LED (LED #2) on the Blue Series On/Off switch when the light (load) is on, find parameter 65 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM31-SN)" - it has the same animations as the VZM30-SN - and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #2 to sync to whatever is set in Parameter 95 (Default of All LED Strip Color - When On).

To adjust the color of the second from the bottom LED (LED #2) on the Blue Series On/Off switch when the light (load) is off, find parameter 66 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM31-SN)" - it has the same animations as the VZM30-SN - and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #2 to sync to whatever is set in Parameter 96 (Default of All LED Strip Color - When Off).

To adjust the second from the bottom LED's brightness (LED #2) on the Blue Series On/Off switch when the light (load) is on, find parameter 67 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #2 to sync to whatever is set in Parameter 97 (Default of All LED Strip Intensity - When On).

To adjust the second from the bottom LED's brightness (LED #2) on the Blue Series On/Off switch when the light (load) is off, find parameter 68 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #2 to sync to whatever is set in Parameter 98 (Default of All LED Strip Intensity - When Off).

To adjust the color of the third from the bottom LED (LED #3) on the Blue Series On/Off switch when the light (load) is on, find parameter 70 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM31-SN)" - it has the same animations as the VZM30-SN - and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #3 to sync to whatever is set in Parameter 95 (Default of All LED Strip Color - When On).

To adjust the color of the third from the bottom LED (LED #3) on the Blue Series On/Off switch when the light (load) is off, find parameter 71 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM31-SN)" - it has the same animations as the VZM30-SN - and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #3 to sync to whatever is set in Parameter 96 (Default of All LED Strip Color - When Off).

To adjust the third from the bottom LED's brightness (LED #3) on the Blue Series On/Off switch when the light (load) is on, find parameter 72 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #3 to sync to whatever is set in Parameter 97 (Default of All LED Strip Intensity - When On).

To adjust the third from the bottom LED's brightness (LED #3) on the Blue Series On/Off switch when the light (load) is off, find parameter 73 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #3 to sync to whatever is set in Parameter 98 (Default of All LED Strip Intensity - When Off).

To adjust the color of the middle LED (LED #4) on the Blue Series On/Off switch when the light (load) is on, find parameter 75 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM31-SN)" - it has the same animations as the VZM30-SN - and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #4 to sync to whatever is set in Parameter 95 (Default of All LED Strip Color - When On).

To adjust the color of the middle LED (LED #4) on the Blue Series On/Off switch when the light (load) is off, find parameter 76 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM31-SN)" - it has the same animations as the VZM30-SN - and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #4 to sync to whatever is set in Parameter 96 (Default of All LED Strip Color - When Off).

To adjust the middle LED's brightness (LED #4) on the Blue Series On/Off switch when the light (load) is on, find parameter 77 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #4 to sync to whatever is set in Parameter 97 (Default of All LED Strip Intensity - When On).

To adjust the middle LED's brightness (LED #4) on the Blue Series On/Off switch when the light (load) is off, find parameter 78 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #4 to sync to whatever is set in Parameter 98 (Default of All LED Strip Intensity - When Off).

To adjust the color of the third from the top LED (LED #5) on the Blue Series On/Off switch when the light (load) is on, find parameter 80 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM31-SN)" - it has the same animations as the VZM30-SN - and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #5 to sync to whatever is set in Parameter 95 (Default of All LED Strip Color - When On).

To adjust the color of the third from the top LED (LED #5) on the Blue Series On/Off switch when the light (load) is off, find parameter 81 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM31-SN)" - it has the same animations as the VZM30-SN - and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #5 to sync to whatever is set in Parameter 96 (Default of All LED Strip Color - When Off).

To adjust the the third from the top LED's brightness (LED #5) on the Blue Series On/Off switch when the light (load) is on, find parameter 82 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #5 to sync to whatever is set in Parameter 97 (Default of All LED Strip Intensity - When On).

To adjust the the third from the top LED's brightness (LED #5) on the Blue Series On/Off switch when the light (load) is off, find parameter 83 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #5 to sync to whatever is set in Parameter 98 (Default of All LED Strip Intensity - When Off).

To adjust the color of the second from the top LED (LED #6) on the Blue Series On/Off switch when the light (load) is on, find parameter 85 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM31-SN)" - it has the same animations as the VZM30-SN - and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #6 to sync to whatever is set in Parameter 95 (Default of All LED Strip Color - When On).

To adjust the color of the second from the top LED (LED #6) on the Blue Series On/Off switch when the light (load) is off, find parameter 86 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM31-SN)" - it has the same animations as the VZM30-SN - and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #6 to sync to whatever is set in Parameter 96 (Default of All LED Strip Color - When Off).

To adjust the second from the top LED's brightness (LED #6) on the Blue Series On/Off switch when the light (load) is on, find parameter 87 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #6 to sync to whatever is set in Parameter 97 (Default of All LED Strip Intensity - When On).

To adjust the second from the top LED's brightness (LED #6) on the Blue Series On/Off switch when the light (load) is off, find parameter 88 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #6 to sync to whatever is set in Parameter 98 (Default of All LED Strip Intensity - When Off).

To adjust the color of the top LED (LED #7) on the Blue Series On/Off switch when the light (load) is on, find parameter 90 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM31-SN)" - it has the same animations as the VZM30-SN - and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #7 to sync to whatever is set in Parameter 95 (Default of All LED Strip Color - When On).

To adjust the color of the top LED (LED #7) on the Blue Series On/Off switch when the light (load) is off, find parameter 91 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM31-SN)" - it has the same animations as the VZM30-SN - and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #7 to sync to whatever is set in Parameter 96 (Default of All LED Strip Color - When Off).

To adjust the top LED's brightness (LED #7) on the Blue Series On/Off switch when the light (load) is on, find parameter 92 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #7 to sync to whatever is set in Parameter 97 (Default of All LED Strip Intensity - When On).

To adjust the top LED's brightness (LED #7) on the Blue Series On/Off switch when the light (load) is off, find parameter 93 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #7 to sync to whatever is set in Parameter 98 (Default of All LED Strip Intensity - When Off).

To adjust the color of the LED Bar (LED's 1-7) on the Blue Series On/Off switch when the light (load) is on, find parameter 95 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM31-SN)" - it has the same animations as the VZM30-SN - and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is 170 which is Blue.

To adjust the color of the LED Bar (LED's 1-7) on the Blue Series On/Off switch when the light (load) is off, find parameter 96 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM31-SN)" - it has the same animations as the VZM30-SN - and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is 170 which is Blue.

To adjust the LED Bar's brightness (LED's 1-7) on the Blue Series On/Off switch when the light (load) is on, find parameter 97 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default value is 33 (33%).

To adjust the LED Bar's brightness (LED's 1-7) on the Blue Series On/Off switch when the light (load) is off, find parameter 98 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #4 to sync to whatever is set in Parameter 98 (Default of All LED Strip Intensity - When Off).

Internal Temperature Monitoring is a feature that monitors the internal temperature of your switch and will work in conjunction with the Overheat Protection parameter to shut off your switch if it becomes too hot.

Overheat Protection shuts off your switch once the threshold of 90°C (194°F) is met and will return to normal once the switch reaches 70°C (158°F).

Switch Delay refers to the delay between when you press the switch and the light turns on. By default, there is a 500ms delay to account for multi-taps (scene control). In other words, the switch does not turn on right away because it's waiting for a potential multi-tap. You can turn this delay off, but you will lose multi-tap control on the paddle (you will still have it on the config/favorites button).

Local Protection refers to whether or not the load of the switch can be controlled via paddle presses (locally). You can set it so the switch is locked from turning on and off from the paddle.

Remote Protection refers to whether or not the load of the switch can be controlled remotely. You can set it so the switch is locked from turning on and off from your hub's app.

One LED Mode will set your switch to mimic our Gen 2 On/Off switch where only the bottom LED (#1) will operate.

Firmware Progress LED refers to the animation that runs during a firmware update. You can choose to keep this animation on or turn it off.

Double-Tap Up to Max refers to enabling double-tapping up on the paddle and having the switch turn on to 100% instantly.

Double-Tap Down to Min refers to enabling double-tapping down on the paddle and having the switch turn down to 1% instantly.

Double-Tap Up to Level allows you to set the specific dim level for when you double-tap on the up paddle (NOTE: Level controls are only available for Zigbee Bindings).

Double-Tap Down to Level allows you to set the specific dim level for when you double-tap on the down paddle (NOTE: Level controls are only available for Zigbee Bindings).

Aux Switch Unique Scenes allows you to have different scenes at the aux switch then you do at the smart switch. In other words, you can create a double-tap scene on the aux switch that is different than the double-tap scene on the smart switch.

Clear Notifications by Double-Tapping the Config/Favorites Button allows you to turn on or off the ability to double-tap the config/favorites button to clear active notifications.

Your switch has a built in temperature sensor on its Zigbee chipset that will monitor the internal temperature of the Blue Series On/Off switch. This will work in conjunction with Parameter 33 (Overheat Protection) in that it will shut off the switch if the internal temperature reaches 90°C (194°F) and will return to normal once the switch reaches 70°C (158°F). This is a read only parameter so there is no default.

Your Blue Series On/Off switch has built a in overheating protection feature that will shut off the switch if it becomes too hot. When Parameter 32 (Internal Temperature Monitoring) exceeds 90°C (194°F), the Blue Series On/Off switch will shut the load off, change to On/Off + Full Sine Mode, disable all functionality (you will not be able to control the switch as all buttons will be disabled) and the LED Bar will slow blink red. This notification cannot be cleared until the switch cools down to 70°C (158°F) at which point the notification can be cleared. Please note, when returning to normal state, the switch will not automatically turn on the load, so if you are utilizing Smart Bulb Mode, you will have to set it up again. This is a read only parameter so there is no default.

To adjust the time between when you press the paddle and the light turns on/off, find Parameter 50 and adjust accordingly. A 0 value allows for, "instant on/off" and will turn the light on/off as soon as you let go of the paddle. Please note that if you set the switch to, "instant on/off" it will disable multi-tap scene control from the paddle (you will still have multi-tap scene control from the config/favorites button). The default is a 500 millisecond delay.

If you have your Blue Series On/Off switch setup in a multi-way setting with an Auxiliary Switch, you can choose to have your Aux switch have different scenes than your Blue Series On/Off. In other words, if you have a scene where you double-tap your Blue Series On/Off switch to activate a bedtime scene, you can double-tap your Aux switch with a different scene (ie: Movie Scene). The default is 0, which disables this feature and has the Aux switch mimic the Blue Series On/Off switch (ie: double tap scene on the aux = double tap scene on the Blue Dimmer).

To disable button presses at the Blue Series On/Off switch (ie: local at the switch), turn Parameter 256 to 1. By default this parameter is set to 0, which disables this feature. Please note that this is different than Smart Bulb Mode (Parameter 52), which still allows commands to be sent when the switch is pressed locally.

To disable button presses of the Blue Series On/Off switch remotely (ie: via an app/web UX), turn Parameter 257 to 1. By default this parameter is set to 0, which disables this feature. Please note that this is different than Smart Bulb Mode (Parameter 52), which still allows commands to be sent when the switch is pressed locally.

To mimic your Gen 2 On/Off switch that only had one LED on your Blue Series On/Off switch, turn Parameter 259 to 1. By default this parameter is set to 0, has the switch mimic the Gen 2 Dimmer switch which had seven (7) led's.

During each firmware update, the Blue Series On/Off Switch has an animation where the LED Bar will light up to the level the firmware update is at (ie: if the LED Bar is halfway up the switch, the firmware update is 50% completed). If you'd like to disable the Firmware Update LED Animation, please change Parameter 260 to 0. By default this feature is set to 1, which enables the animation.

If you'd like to turn off the feature to double-tap the config/favorites button to clear active notifications on your Blue Series On/Off Switch, change Parameter 262 to 1. By default this feature is set to 0, which enables this feature.