Please use this document as a resource to understand the various parameters on your Blue Series mmWave Presence Dimmer switch. We try to keep this up-to-date, but as we constantly change our firmware, there may be a mistake. Please reach out if you see anything that needs to be corrected.

Please see the table below for a quick reference guide to the parameters on the Blue Series mmWave Presence Dimmer switch (VZM32-SN). The table is meant to provide a high level view of all the parameters. For a full explanation of each parameter, please click on the hyperlink in each cell to be taken down the page to the appropriate section.

Below we'll list out the parameter number, description, range, default value, size, firmware version it was implemented and an example of how to use it.

AC Power Type is a read only parameter that shows whether or not the switch is in neutral or non-neutral mode.

Switch Mode refers to the switch being in either On/Off or Dimmer mode.

Switch Type refers to the type of wiring installation your switch is in: Single Pole, 3-Way Aux or Full Sine Wave.

Leading/Trailing Edge refers to the way your switch handles the lights it's controlling. You can switch between each one to get the best compatibility with your bulbs. However, Trailing Edge is only available in neutral single-pole and neutral multi-way with an aux setups.

Smart Bulb Mode is a mode that allows your switch to be used with smart bulbs that are wired to the switch (ie: it locks in full power and sends digital signals to the hub to turn on/off/dim the smart bulb rather than cutting power to the bulb).

To see whether or not your Blue Series mmWave Presence Dimmer Switch is in neutral or non-neutral mode, please look for Parameter 21 in your hubs user interface (NOTE: This is a read only parameter that cannot be changed, so it may not show up on some hub user interfaces such as SmartThings).

To change your Blue Series mmWave Presence Dimmer Switch from On/Off to Dimmer or Dimmer to On/Off, please select Parameter 258 and adjust accordingly with 0 being Dimmer and 1 being On/Off which is also the default setting.

To program your Blue Series mmWave Presence Dimmer switch which installation type it's in (ie: Single Pole or 3-Way Aux) you'll want to change Parameter 22 and enter in 0 for Single Pole or 1 for Multi-Way (3-Way) with an Auxiliary / Add-On switch (which is also the default).

Dimming speed refers to how fast or slow the light turns on when you change the dim level either remotely or locally (at the switch) such as from 10-20%, 60-80%, etc.

Ramp rate refers to how fast or slow the light turns on when you either remotely or locally (at the switch) bring the switch from off to on (or on to off).

To change the remote dimming speed for dimming up on your Blue Series mmWave Presence Dimmer Switch, you would select Parameter 1 within your hub and then input a range of 0-126, with each interval equating to 100 milliseconds and the default being 2.5 seconds.

To change the dimming speed at the switch (locally) for dimming up on your Blue Series mmWave Presence Dimmer Switch, you would select Parameter 2 within your hub and then input a range of 0-127, with each interval equating to 100 milliseconds and the default being that the switch will default to whatever is selected in Parameter 1.

To change the remote dimming speed for dimming down on your Blue Series mmWave Presence Dimmer Switch, you would select Parameter 5 within your hub and then input a range of 0-126, with each interval equating to 100 milliseconds and the default being that the switch will default to whatever is selected in Parameter 1.

To change the dimming speed at the switch (locally) for dimming down on your Blue Series mmWave Presence Dimmer Switch, you would select Parameter 6 within your hub and then input a range of 0-127, with each interval equating to 100 milliseconds and the default being that the switch will default to whatever is selected in Parameter 2.

To change the remote ramp rate for how fast your Blue Series mmWave Presence Dimmer Switch goes from off to on, you would select Parameter 3 within your hub and then input a range of 0-127, with each interval equating to 100 milliseconds and the default being that the switch will default to whatever is selected in Parameter 1.

To change the remote ramp rate for how fast your Blue Series mmWave Presence Dimmer Switch goes from off to on, you would select Parameter 4 within your hub and then input a range of 0-127, with each interval equating to 100 milliseconds and the default being that the switch will default to whatever is selected in Parameter 3.

To change the ramp rate for how fast your Blue Series mmWave Presence Dimmer Switch goes from on to off remotely in your app, you would select Parameter 7 within your hub and then input a range of 0-127, with each interval equating to 100 milliseconds and the default being that the switch will default to whatever is selected in Parameter 3.

To change the ramp rate for how fast your Blue Series mmWave Presence Dimmer Switch goes from on to off locally at the switch, you would select Parameter 8 within your hub and then input a range of 0-127, with each interval equating to 100 milliseconds and the default being that the switch will default to whatever is selected in Parameter 4.

Minimum Dim Level refers to the minimum level the light switch will dim to.

Maximum Dim Level refers to the maximum level the light switch will dim to.

Invert Switch refers to inverting the switch (where tapping up on the switch will turn the switch off and tapping down on the switch will turn the switch on)

Auto-Off Timer refers to the switch being turned off after a certain amount of time (in seconds).

To change the minimum dim level for how low your Blue Series mmWave Presence Dimmer Switch dims to, you would select Parameter 9 within your hub and then input a range of 1-253, where the lower the numeric value equals the lower the minimum dim level (1 = ~1%) and the higher the numeric value equals the higher the minimum dim level (253 = ~99%) with the default being that the switch will be at 1%.

This is typically used for fixing flickering bulbs or calibrating the bulb if it shuts off prior to 1%.

To change the maximum dim level for how low your Blue Series mmWave Presence Dimmer Switch dims to, you would select Parameter 10 within your hub and then input a range of 2-254, where the lower the numeric value equals the lower the maximum dim level (2 = ~2%) and the higher the numeric value equals the higher the maximum dim level (254 = ~100%) with the default being that the switch will be at 100%.

This is typically used for calibrating the bulb if reaches the maximum level before 100%.

To invert your Blue Series mmWave Presence Dimmer Switch (ie: tapping on the up button turns your light off and tapping on the down button turns your light on), you would select Parameter 11 within your hub and then select either 0 to keep it non-inverted or 1 to invert it with the default being that the switch is not inverted (value of 0).

To set an auto-off timer where you can have your Blue Series mmWave Presence Dimmer Switch turn off after a certain amount of seconds, you would select Parameter 12 within your hub and then input a range of 0-32767, where each interval is a second.

Default Level - Local refers to the default dim level the switch goes to when turned on at the switch (ie: if you set the default level to 60%, that's the percentage the switch turns on to when you turn it on).

Default Level - Remote refers to the default dim level the switch goes to when turned on remotely via the app (ie: if you set the default level to 60%, that's the percentage the switch turns on to when you turn it on).

Level After Power Restored refers to the level the switch will return to when power is restored to it (ie: after a power outage).

LED Indicator Timeout changes the amount of time (in seconds) the RGB Bar shows the Dim Level (ie: if you are actively dimming the light, the LED Bar will show you approximately what level the light is at -- the timeout is the time that indicator shows once you let go of the paddle)

To set the default level your Blue Series mmWave Presence Dimmer Switch turns on to when you manually press the switch, you would select Parameter 13 within your hub and then input a range of 0-255, where zero (0) equals off, 255 equals the last level the switch was set at, the lower the numeric value equals a lower dim level (1 = ~1%) and the higher the numeric value equals a higher dim level (254 = ~100%) with the default being that the switch will return to the prior state it was in.

To set the default level your Blue Series mmWave Presence Dimmer Switch turns on to when you turn on your switch remotely (via an app), you would select Parameter 14 within your hub and then input a range of 0-255, where zero (0) equals off, 255 equals the last level the switch was set at, the lower the numeric value equals a lower dim level (1 = ~1%) and the higher the numeric value equals a higher dim level (254 = ~100%) with the default being that the switch will return to the prior state it was in.

To set the behavior that your Blue Series mmWave Presence Dimmer Switch enacts after a power outage, you would select Parameter 15 within your hub and then input a range of 0-255, where zero (0) equals off, 255 equals the last level the switch was set at, the lower the numeric value equals a lower dim level (1 = ~1%) and the higher the numeric value equals a higher dim level (254 = ~100%) with the default being that the switch will return to the prior state it was in.

To adjust the time that the LED Bar displays the value of what your Blue Series mmWave Presence Dimmer Switch is at (ie: on/off, dim level), you would select Parameter 17 within your hub and then input a range of 0-11, where zero (0) equals always off, each interval equals one second and 11 equals always on.

Active Power Reports refer to the reporting of the power level change and will result in a new power report being sent in wattage (W).

Periodic Power & Energy Reports refer to the time period between consecutive power and energy reports being sent (in seconds).

Energy Reports refer to the reporting of the energy level change and will result in a new energy report being sent in kilowatt hours (kWh).

To adjust the threshold at which a power report is sent based on a change in Wattage on your Blue Series mmWave Presence Dimmer Switch, you would select Parameter 18 within your hub and then input a range of 0-32767, where zero disables the reports and each interval equals 0.1 Watt.

To adjust the time period at which consecutive power or energy reports are sent on your Blue Series mmWave Presence Dimmer Switch, you would select Parameter 19 within your hub and then input a range of 0-32767, where zero disables the reports and each interval equals 1 second.

To adjust the threshold at which an energy report is sent based on a change in kilowatt hours on your Blue Series mmWave Presence Dimmer Switch, you would select Parameter 20 within your hub and then input a range of 0-32767, where zero disables the reports and each interval equals 0.01 kilowatt hours (kWh).

Please use the chart below to understand what parameters align with what LED on the switch. For a visual example, please visit the Inovelli Toolbox which will show you what the various animations look like (be sure to select, "On\Off + Dimmer Switch (VZM32-SN)").

To adjust the color of the bottom LED (LED #1) on the Blue Series mmWave Presence Dimmer switch when the light (load) is on, find parameter 60 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM32-SN)" and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #1 to sync to whatever is set in Parameter 95 (Default of All LED Strip Color - When On).

To adjust the color of the bottom LED (LED #1) on the Blue Series mmWave Presence Dimmer switch when the light (load) is off, find parameter 61 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM32-SN)" and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #1 to sync to whatever is set in Parameter 96 (Default of All LED Strip Color - When Off).

To adjust the bottom LED's brightness (LED #1) on the Blue Series mmWave Presence Dimmer switch when the light (load) is on, find parameter 62 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #1 to sync to whatever is set in Parameter 97 (Default of All LED Strip Intensity - When On).

To adjust the bottom LED's brightness (LED #1) on the Blue Series mmWave Presence Dimmer switch when the light (load) is off, find parameter 63 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #1 to sync to whatever is set in Parameter 98 (Default of All LED Strip Intensity - When Off).

To adjust the color of the second from the bottom LED (LED #2) on the Blue Series mmWave Presence Dimmer switch when the light (load) is on, find parameter 65 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM32-SN)" and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #2 to sync to whatever is set in Parameter 95 (Default of All LED Strip Color - When On).

To adjust the color of the second from the bottom LED (LED #2) on the Blue Series mmWave Presence Dimmer switch when the light (load) is off, find parameter 66 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM32-SN)" and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #2 to sync to whatever is set in Parameter 96 (Default of All LED Strip Color - When Off).

To adjust the second from the bottom LED's brightness (LED #2) on the Blue Series mmWave Presence Dimmer switch when the light (load) is on, find parameter 67 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #2 to sync to whatever is set in Parameter 97 (Default of All LED Strip Intensity - When On).

To adjust the second from the bottom LED's brightness (LED #2) on the Blue Series mmWave Presence Dimmer switch when the light (load) is off, find parameter 68 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #2 to sync to whatever is set in Parameter 98 (Default of All LED Strip Intensity - When Off).

To adjust the color of the third from the bottom LED (LED #3) on the Blue Series mmWave Presence Dimmer switch when the light (load) is on, find parameter 70 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM32-SN)" and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #3 to sync to whatever is set in Parameter 95 (Default of All LED Strip Color - When On).

To adjust the color of the third from the bottom LED (LED #3) on the Blue Series mmWave Presence Dimmer switch when the light (load) is off, find parameter 71 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM32-SN)" and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #3 to sync to whatever is set in Parameter 96 (Default of All LED Strip Color - When Off).

To adjust the third from the bottom LED's brightness (LED #3) on the Blue Series mmWave Presence Dimmer switch when the light (load) is on, find parameter 72 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #3 to sync to whatever is set in Parameter 97 (Default of All LED Strip Intensity - When On).

To adjust the third from the bottom LED's brightness (LED #3) on the Blue Series mmWave Presence Dimmer switch when the light (load) is off, find parameter 73 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #3 to sync to whatever is set in Parameter 98 (Default of All LED Strip Intensity - When Off).

To adjust the color of the middle LED (LED #4) on the Blue Series mmWave Presence Dimmer switch when the light (load) is on, find parameter 75 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM32-SN)" and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #4 to sync to whatever is set in Parameter 95 (Default of All LED Strip Color - When On).

To adjust the color of the middle LED (LED #4) on the Blue Series mmWave Presence Dimmer switch when the light (load) is off, find parameter 76 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM32-SN)" and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #4 to sync to whatever is set in Parameter 96 (Default of All LED Strip Color - When Off).

To adjust the middle LED's brightness (LED #4) on the Blue Series mmWave Presence Dimmer switch when the light (load) is on, find parameter 77 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #4 to sync to whatever is set in Parameter 97 (Default of All LED Strip Intensity - When On).

To adjust the middle LED's brightness (LED #4) on the Blue Series mmWave Presence Dimmer switch when the light (load) is off, find parameter 78 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #4 to sync to whatever is set in Parameter 98 (Default of All LED Strip Intensity - When Off).

To adjust the color of the third from the top LED (LED #5) on the Blue Series mmWave Presence Dimmer switch when the light (load) is on, find parameter 80 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM32-SN)" and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #5 to sync to whatever is set in Parameter 95 (Default of All LED Strip Color - When On).

To adjust the color of the third from the top LED (LED #5) on the Blue Series mmWave Presence Dimmer switch when the light (load) is off, find parameter 81 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM32-SN)" and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #5 to sync to whatever is set in Parameter 96 (Default of All LED Strip Color - When Off).

To adjust the the third from the top LED's brightness (LED #5) on the Blue Series mmWave Presence Dimmer switch when the light (load) is on, find parameter 82 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #5 to sync to whatever is set in Parameter 97 (Default of All LED Strip Intensity - When On).

To adjust the the third from the top LED's brightness (LED #5) on the Blue Series mmWave Presence Dimmer switch when the light (load) is off, find parameter 83 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #5 to sync to whatever is set in Parameter 98 (Default of All LED Strip Intensity - When Off).

To adjust the color of the second from the top LED (LED #6) on the Blue Series mmWave Presence Dimmer switch when the light (load) is on, find parameter 85 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM32-SN)" and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #6 to sync to whatever is set in Parameter 95 (Default of All LED Strip Color - When On).

To adjust the color of the second from the top LED (LED #6) on the Blue Series mmWave Presence Dimmer switch when the light (load) is off, find parameter 86 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM32-SN)" and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #6 to sync to whatever is set in Parameter 96 (Default of All LED Strip Color - When Off).

To adjust the second from the top LED's brightness (LED #6) on the Blue Series mmWave Presence Dimmer switch when the light (load) is on, find parameter 87 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #6 to sync to whatever is set in Parameter 97 (Default of All LED Strip Intensity - When On).

To adjust the second from the top LED's brightness (LED #6) on the Blue Series mmWave Presence Dimmer switch when the light (load) is off, find parameter 88 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #6 to sync to whatever is set in Parameter 98 (Default of All LED Strip Intensity - When Off).

To adjust the color of the top LED (LED #7) on the Blue Series mmWave Presence Dimmer switch when the light (load) is on, find parameter 90 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM32-SN)" and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #7 to sync to whatever is set in Parameter 95 (Default of All LED Strip Color - When On).

To adjust the color of the top LED (LED #7) on the Blue Series mmWave Presence Dimmer switch when the light (load) is off, find parameter 91 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM32-SN)" and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is for LED #7 to sync to whatever is set in Parameter 96 (Default of All LED Strip Color - When Off).

To adjust the top LED's brightness (LED #7) on the Blue Series mmWave Presence Dimmer switch when the light (load) is on, find parameter 92 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #7 to sync to whatever is set in Parameter 97 (Default of All LED Strip Intensity - When On).

To adjust the top LED's brightness (LED #7) on the Blue Series mmWave Presence Dimmer switch when the light (load) is off, find parameter 93 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #7 to sync to whatever is set in Parameter 98 (Default of All LED Strip Intensity - When Off).

To adjust the color of the LED Bar (LED's 1-7) on the Blue Series mmWave Presence Dimmer switch when the light (load) is on, find parameter 95 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM32-SN)" and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is 170 which is Blue.

To adjust the color of the LED Bar (LED's 1-7) on the Blue Series mmWave Presence Dimmer switch when the light (load) is off, find parameter 96 in your hub's UI and change accordingly. The easiest way to determine a color's value is to go to the Inovelli Toolbox, select, "On\Off + Dimmer Switch (VZM32-SN)" and then select, "LED" and use the slider to select a color (ie: 170 is blue). The default is 170 which is Blue.

To adjust the LED Bar's brightness (LED's 1-7) on the Blue Series mmWave Presence Dimmer switch when the light (load) is on, find parameter 97 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default value is 33 (33%).

To adjust the LED Bar's brightness (LED's 1-7) on the Blue Series mmWave Presence Dimmer switch when the light (load) is off, find parameter 98 in your hub's UI and change accordingly. The lower the number, the lower the intensity (ie: 0 = Off, 10 = 10%, 100 = 100%, etc). The default is for LED #4 to sync to whatever is set in Parameter 98 (Default of All LED Strip Intensity - When Off).

To define how the switch should behave in response to presence on the Blue Series mmWave Presence Dimmer switch, find parameter 110 in your hub's UI and change accordingly. Suggestion: Start with 1 for typical occupancy-based lighting. Try other modes to suit your environment.

To eliminate false presence detection caused by fans, curtains, or similar repetitive motion on the Blue Series mmWave Presence Dimmer switch, find parameter 111 in your hub's UI and change accordingly. To set an Interference Area: 1. Make sure the interfering object (e.g. ceiling fan) is running, 2. Leave the room so no actual presence is detected, 3. In your hub, select the option labeled "Set Interference Area), 4. The calibration will complete almost instantly. (The switches LED bar will begin to flash orange for 30 seconds. After re-entering the room you can look for this behavior as confirmation that the interference area was programmed). Now, when the object is in motion, it will be ignored by the sensor. You can use this feature alongside range settings 101-106 for best results.

To adjust how sensitive the sensor is to presence on the Blue Series mmWave Presence Dimmer switch, find parameter 112 in your hub's UI and change accordingly. The lower the number, the lower the sensitivity (ie: 0 = Low, 1 = Medium, 2 = High). The default is 2 = High to detect even slight presence (ideal for continuous occupancy)

To control how quickly the sensor responds after detecting presence on the Blue Series mmWave Presence Dimmer switch, find parameter 113 in your hub's UI and change accordingly. The lower the number, the high the delay (ie: 0 = Low, 1 = Medium, 2 = Fast). The default is 2 = Fast. Use this to prevent overly fast triggering or tune responsiveness based on how the room is used.

To set how long the load remains on after presence is no longer detected on the Blue Series mmWave Presence Dimmer switch, find parameter 114 in your hub's UI and change accordingly. The lower the number, the lower the load remains on after presence (ie: 5 = 5 seconds). The default is 10 seconds.

To apply predefined presence zones quickly on the Blue Series mmWave Presence Dimmer switch, find parameter 117 in your hub's UI and change accordingly. The lower the number, the lower the room size. Tip: Start with a preset, then fine=tune using the range parameters for precise control.

Internal Temperature Monitoring is a feature that monitors the internal temperature of your switch and will work in conjunction with the Overheat Protection parameter to shut off your switch if it becomes too hot.

Overheat Protection shuts off your switch once the threshold of 90°C (194°F) is met and will return to normal once the switch reaches 70°C (158°F).

Switch Delay refers to the delay between when you press the switch and the light turns on. By default, there is a 500ms delay to account for multi-taps (scene control). In other words, the switch does not turn on right away because it's waiting for a potential multi-tap. You can turn this delay off, but you will lose multi-tap control on the paddle (you will still have it on the config/favorites button).

Local Protection refers to whether or not the load of the switch can be controlled via paddle presses (locally). You can set it so the switch is locked from turning on and off from the paddle.

Remote Protection refers to whether or not the load of the switch can be controlled remotely. You can set it so the switch is locked from turning on and off from your hub's app.

One LED Mode will set your switch to mimic our Gen 2 On/Off switch where only the bottom LED (#1) will operate.

Firmware Progress LED refers to the animation that runs during a firmware update. You can choose to keep this animation on or turn it off.

Disable Relay, "Click" Sound refers to disabling the clicking sound of the internal relay.

Double-Tap Up to Max refers to enabling double-tapping up on the paddle and having the switch turn on to 100% instantly.

Double-Tap Down to Min refers to enabling double-tapping down on the paddle and having the switch turn down to 1% instantly.

Double-Tap Up to Level allows you to set the specific dim level for when you double-tap on the up paddle.

Double-Tap Down to Level allows you to set the specific dim level for when you double-tap on the down paddle.

Non-Neutral Output allows you to increase the power output in non-neutral mode. By default the switch throttles the power output in non-neutral to prevent flickering. If you experience flickering when turning this feature on, adjust Parameter 10 (Max Dim Level).

LED Bar Scaling allows you to match the scaling of any Gen 2 switches you have.

Aux Switch Unique Scenes allows you to have different scenes at the aux switch then you do at the smart switch. In other words, you can create a double-tap scene on the aux switch that is different than the double-tap scene on the smart switch.

Binding Default Level allows you to match the default level parameter (Parameter 13 & 14) when using Zigbee Bindings.

Clear Notifications by Double-Tapping the Config/Favorites Button allows you to turn on or off the ability to double-tap the config/favorites button to clear active notifications.

To adjust the voltage output in non-neutral mode for your Blue Series mmWave Presence Dimmer Switch, you'll want to adjust Parameter 25. By default, the switch throttles the output of the load in non-neutral mode so that it can effectively communicate with the aux switch (if needed) and/or minimize flickering. When the output is at its maximum, all the power to the switch is taken away by the bulb, which leads to signal instability, bulb flickering and can cause the switch to continuously reboot. You can remove this throttle and test the instability if you want your bulbs to be brighter by setting the value to 1. The default is 0, which puts the throttle on the switch.
​
​NOTE: If you remove the throttle and experience flickering, you can change Parameter 10 (Max Dim Level) until the flickering stops.

Your switch has a built in temperature sensor on its Zigbee chipset that will monitor the internal temperature of the Blue Series mmWave Presence Dimmer switch. This will work in conjunction with Parameter 33 (Overheat Protection) in that it will shut off the switch if the internal temperature reaches 90°C (194°F) and will return to normal once the switch reaches 70°C (158°F). This is a read only parameter so there is no default.

Your Blue Series mmWave Presence Dimmer switch has built a in overheating protection feature that will shut off the switch if it becomes too hot. When Parameter 32 (Internal Temperature Monitoring) exceeds 90°C (194°F), the Blue Series mmWave Presence Dimmer switch will shut the load off, change to On/Off + Full Sine Mode, disable all functionality (you will not be able to control the switch as all buttons will be disabled) and the LED Bar will slow blink red. This notification cannot be cleared until the switch cools down to 70°C (158°F) at which point the notification can be cleared. Please note, when returning to normal state, the switch will not automatically turn on the load, so if you are utilizing Smart Bulb Mode, you will have to set it up again. This is a read only parameter so there is no default.

To adjust the time between when you press the paddle and the light turns on/off, find Parameter 50 and adjust accordingly. A 0 value allows for, "instant on/off" and will turn the light on/off as soon as you let go of the paddle. Please note that if you set the switch to, "instant on/off" it will disable multi-tap scene control from the paddle (you will still have multi-tap scene control from the config/favorites button). The default is a 500 millisecond delay.

To see how many devices your Blue Series mmWave Presence Dimmer Switch is bound to, please look for Parameter 51 in your hubs user interface (NOTE: This is a read only parameter that cannot be changed, so it may not show up on some hub user interfaces such as SmartThings).

If you'd like your Blue Series mmWave Presence Dimmer switch to easily turn onto 100% via a double-tap on the up (top) paddle, turn on Parameter 53 (if you'd like to set a specific value other than 100%, then also turn on Parameter 55 and set the level). The default is 0, which has this feature turned off.

If you'd like your Blue Series mmWave Presence Dimmer switch to easily turn down to 1% via a double-tap on the down (bottom) paddle, turn on Parameter 54 (if you'd like to set a specific value other than 1%, then also turn on Parameter 56 and set the level). The default is 0, which has this feature turned off.

If you'd like your Blue Series mmWave Presence Dimmer switch to easily turn onto a certain dim percentage via a double-tap on the up (top) paddle, turn on Parameter 55 (also remember to turn on Parameter 53 - 2x Up to P55). The lower the numeric value equals a lower dim level (1 = ~1%) and the higher the numeric value equals a higher dim level (254 = ~100%) with the default being 254 (100%).

If you'd like your Blue Series mmWave Presence Dimmer switch to easily turn down to a certain dim percentage via a double-tap on the down (bottom) paddle, turn on Parameter 56 (also remember to turn on Parameter 54 - 2x Down to P56). The lower the numeric value equals a lower dim level (1 = ~1%) and the higher the numeric value equals a higher dim level (254 = ~100%) with the default being 2 (~1%).

If you'd like your Blue Series mmWave Presence Dimmer switches LED Bar scaling to match your Gen 2 (LZWxx) switches LED Bar scaling, set Parameter 100 to 1. The default is 0, which keeps the Blue Series mmWave Presence Dimmer switches default scaling.

If you have your Blue Series mmWave Presence Dimmer switch setup in a multi-way setting with an Auxiliary Switch, you can choose to have your Aux switch have different scenes than your Blue Series mmWave Presence Dimmer. In other words, if you have a scene where you double-tap your Blue Series mmWave Presence Dimmer switch to activate a bedtime scene, you can double-tap your Aux switch with a different scene (ie: Movie Scene). The default is 0, which disables this feature and has the Aux switch mimic the Blue Series mmWave Presence Dimmer switch (ie: double tap scene on the aux = double tap scene on the Blue Dimmer).

If your Blue Series mmWave Presence Dimmer Switch is bound to a Zigbee smart bulb and you'd like to set a default level when turned on, change Parameter 125 to 1 (and also set the default level parameters - 13 & 14). By default this parameter is set to 0, which disables this feature.

To disable button presses at the Blue Series mmWave Presence Dimmer switch (ie: local at the switch), turn Parameter 256 to 1. By default this parameter is set to 0, which disables this feature. Please note that this is different than Smart Bulb Mode (Parameter 52), which still allows commands to be sent when the switch is pressed locally.

To disable button presses of the Blue Series mmWave Presence Dimmer switch remotely (ie: via an app/web UX), turn Parameter 257 to 1. By default this parameter is set to 0, which disables this feature. Please note that this is different than Smart Bulb Mode (Parameter 52), which still allows commands to be sent when the switch is pressed locally.

To mimic your Gen 2 On/Off switch that only had one LED on your Blue Series mmWave Presence Dimmer switch, turn Parameter 259 to 1. By default this parameter is set to 0, has the switch mimic the Gen 2 Dimmer switch which had seven (7) led's.

During each firmware update, the Blue Series mmWave Presence Dimmer Switch has an animation where the LED Bar will light up to the level the firmware update is at (ie: if the LED Bar is halfway up the switch, the firmware update is 50% completed). If you'd like to disable the Firmware Update LED Animation, please change Parameter 260 to 0. By default this feature is set to 1, which enables the animation.

If you'd like to turn off the feature to double-tap the config/favorites button to clear active notifications on your Blue Series mmWave Presence Dimmer Switch, change Parameter 262 to 1. By default this feature is set to 0, which enables this feature.