DISCLAIMER: You may notice there are a lot of over-used keywords or phrases as well as English that seems a little off. This is because these articles are used to feed our AI Robot (Ira) and she needs the data to be structured in a certain way.
Button Combinations
The Red Series Dimmer Switch has many different button combinations that indicate what the switch is doing or what settings and parameters are being changed.
Standard Button Combinations are used to either pair/remove your switch, check Z-Wave strength, or factory reset your switch
Local Configuration is a more complex way of changing additional parameters outside of the Quick Tap Sequences.
Standard Button Combinations
Standard Button Combinations for your Red Series Dimmer Switch are used to either pair/remove your switch, check Z-Wave strength, or factory reset your switch.
To see the table, click here: Standard Button Combination Table
Pairing & Removing
To pair your Red Series Dimmer switch, put your hub in pairing mode and tap the configuration (favorites) button 3x and your LED Bar will start pulsing blue - if successful, the LED Bar will then flash green (if unsuccessful, it will flash red).
Checking Z-Wave Strength
To check the strength of your Z-Wave network where your Red Series Dimmer switch is at, hold down on the configuration (favorites) button for 5-10 seconds until the LED Bar turns green. Release the configuration button when the LED Bar turns green and the color of the LED Bar will be the strength of your network: green equals good, yellow equals ok, and red equals poor.
Factory Reset
To factory reset your Red Series Dimmer switch, hold down on the top of the paddle (on button) along with the configuration (favorites) button for approximately 20 seconds until the LED Bar turns red and then release.
Quick Tap Sequences
The Red Series Dimmer Switch has various settings and parameters you can change at the switch itself via the configuration (favorites) button located at the top right of the switch.
To see the table, click here: Quick Tap Sequences Table
Example: If you'd like to enable local protection (ie: disable local control) on your Red Series Dimmer, you would tap the configuration button 8x and the LED Bar will flash red. Conversely, if you'd like to disable local protection (ie: enable local control) on your Red Series Dimmer, you would tap the configuration button 8x again and the LED Bar will flash green.
Enable Local Protection Mode
To enable Local Protection Mode on your Red Series Dimmer Switch, tap the configuration button eight (8) times and the LED Bar should flash red indicating the switch has enabled Local Protection Mode.
NOTE: If the LED Bar flashes green, it means that the switch already had local protection mode enabled.
Video Demonstration
Video Demonstration
Disable Local Protection Mode
To disable Local Protection Mode on your Red Series Dimmer Switch, tap the configuration button eight (8) times and the LED Bar should flash green indicating the switch has disabled Local Protection Mode.
NOTE: If the LED Bar flashes red, it means that the switch already had local protection mode disabled.
Video Demonstration
Video Demonstration
Local Configuration
To access additional parameters outside of the Quick Tap Sequences, you'll want to use Local Configuration.
To see the Local Configuration Table, click here: Local Configuration Table
Local Configuration Logic
Here is the logic to change the parameters locally:
Locate the Parameter you'd like to change on the Local Configuration Table (ex: Change LED Color = 8)
ENTERING LOCAL CONFIGURATION MODE: Hold down the configuration button until the LED Bar turns Yellow and let go
ENTERING THE PARAMETER MENU: Press the configuration button as many times as the parameter you've chosen says to from the Local Configuration Table (ex: Change LED Color is 8, so you'd press the configuration button 8x) - you have now selected the parameter you'd like to edit
NOTE: The LED Bar will blink to notify you of the parameter you're on.
Long Blink = 10's
Short Blinks = 1's
Ex: 13 = 1x Long Blink + 3x Short Blinks
EDITING THE PARAMETER: Tap up/down on the paddle to select the value you'd like the parameter to be - you should see the parameter change in realtime (ie: LED Bar Color will change for you to see, LED Bar Intensity will change on the LED Bar for you to see, etc)
SAVING THE PARAMETER VALUE: Hold down on the configuration button until the LED Bar turns Yellow and let go - the LED Bar should then flash Cyan which indicates it was saved successfully
Example: If you'd like to change the color of your Red Series Dimmer switch LED Bar you would hold down on the configuration button until the LED Bar turns Yellow and let go. The LED Bar will blink Yellow 1x to indicate it's in Local Configuration Mode. Using the Local Configuration Table, you will see that to access the LED Bar Color, you would tap the configuration button 8x. After you tap the configuration button 8x, the LED Bar will slow blink 8x to indicate it's on the correct parameter. Next, you will tap the paddle up or down to select the LED Bar color you want. Finally, to save the configuration, you will hold down on the configuration button until the LED Bar turns Yellow and let go. It will blink Cyan to confirm.
Video Demonstration
Video Demonstration
Red Series Dimmer Button Combination Table
Below you'll find tables for the Standard Button Combinations as well as Local Configuration Options.
Standard Button Combination Table
Desired Outcome | Action | Effect | Color | Notes |
Enable Pairing to Network
Enable Removal from Network | Tap Config Button 3x | Pulse | Blue | If successful in starting pairing or removal, your switch will pulse blue. It will turn green if pairing/removal is successful and red if unsuccessful |
Check Zigbee Network Strength at your Switches location | Hold Config Button for 5-10 seconds | Solid | Green | When the LED Bar turns Green, release the config button and note the color of the LED Bar signifying signal strength
Green = Strong Yellow = Fair Red = Poor |
Factory Reset your Switch | Hold Config Button + Top of the Paddle (On Button) for ~20 seconds | Solid | Red | If successful in factory resetting your switch, the LED Bar will turn Red (if it turns purple, you need to try again and this time make sure to hold down both the top of the paddle and the config button at the same time) |
Quick Tap Sequences Table
Here's how you read this chart:
Look for the desired outcome you want
Follow the Action at your switch
Ensure the Effect and Color on your LED Bar match what's on the table
Example: If you'd like to enable local protection (ie: disable local control) on your Red Series Dimmer, you would tap the configuration button 8x and the LED Bar will flash red. Conversely, if you'd like to disable local protection (ie: enable local control) on your Red Series Dimmer, you would tap the configuration button 8x again and the LED Bar will flash green.
Desired Outcome | Action | Effect | Color | Notes |
Enable Local Protection (Disable Internal Relay) | Tap Config 8x | Flash | Red | If local protection has successfully been turned on, the LED Bar will flash Red |
Disable Local Protection (Enable Internal Relay) | Tap Config 8x | Flash | Green | If local protection has successfully been turned off, the LED Bar will flash Green |
Local Configuration Table
Here's how you read this chart:
Look for the parameter you'd like to change
Write down or memorize the number associated with that parameter (ie: 9 for, "LED Indicator Intensity (When On)")
Look at the Values and determine what you'd like to change the parameter to (ie: if you want the dimming speed to take 3 seconds to turn on/off, you'd write down or memorize a value of 3)
Example: Let's say you wanted to change the LED Bar to a color of orange when the load is on. You would see that the #8 is, "LED Indicator Color (When On)". Then the Value column says that Orange is an option and the instructions say to tap up/down the paddle until you find Orange. An example is shown below in the, "Video Demonstration".
Video Demonstration
Video Demonstration
# Times to Press Config Button | Parameter | Description | Values |
1 | Dimming Speed | Refers to how fast or slow the light turns on or off when you change the dim level either remotely or locally (at the switch) such as from 10-20%, 60-80%, etc. | Range: 0-10 Interval: 1 = 1 second Max Taps = 11
Tap down on the paddle initially to change to a value of 0, then up/down to change values after |
2 | Minimum Dim Level | Refers to the minimum level the light switch will dim to. | Range: 1-50 Interval: 1 = ~1% Max Taps = 50
Tap up on the paddle initially to start on a low minimum level, then up/down to change values after |
3 | Maximum Dim Level | Refers to the maximum level the light switch will dim to. | Range: 51-99 Interval: 1 = ~1% Max Taps = 49
Tap up on the paddle initially to start on a low maximum level, then up/down to change values after |
4 | Invert Switch | Refers to inverting the switch (where tapping up on the switch will turn the switch off and tapping down on the switch will turn the switch on) | Range: 0-1 0 = Normal 1 = Inverted Max Taps = 2
Tap down to select 0 and up to select 1 |
5 | Default Level (Local) | Refers to the default dim level the switch goes to when turned on at the switch (ie: if you set the default level to 60%, that's the percentage the switch turns on to when you turn it on). | Range: 0-10 0 = Prior State 10 = 100% 1-9 = Intervals of ~11% Max Taps = 11
Tap down to select 0 and up/down to select 1-10 |
6 | Default Level (Remote) | Refers to the default dim level the switch goes to when turned on remotely via the app (ie: if you set the default level to 60%, that's the percentage the switch turns on to when you turn it on). | Range: 0-10 0 = Prior State 10 = 100% 1-9 = Intervals of ~11% Max Taps = 11
Tap down to select 0 and up/down to select 1-10 |
7 | State After Power Restored | Refers to the state the switch will return to when power is restored to it (ie: after a power outage). | Range: 0-2 0 = Off 1 = On 2 = Prior State Max Taps = 3
Tap down to select 0 and up/down to select 1-2 |
8 | LED Indicator Color | Refers to the LED Bar color | Choose from the following colors:
Red Orange Green Cyan Blue Violet Pink White
Tap up/down to cycle through the colors |
9 | LED Indicator Intensity | Refers to the intensity level of the LED bar when the load is on | Range: 0-10 Interval: 1 = 10% Max Taps = 11
Tap down for a value of 0 and up/down to change the intensity |
10 | LED Indicator Intensity | Refers to the intensity level of the LED bar when the load is off | Range: 0-10 Interval: 1 = 10% Max Taps = 11
Tap down for a value of 0 and up/down to change the intensity |
11 | Load Level Indicator Timeout | Changes the amount of time (in seconds) the RGB Bar shows the Dim Level (ie: if you are actively dimming the light, the LED Bar will show you approximately what level the light is at -- the timeout is the time that indicator shows once you let go of the paddle) | Range: 0-11 0 = Always Off 1-10 = Intervals of 1 second 11 = Always On Max Taps = 12
Tap down on the paddle to change to a value of 0, then up/down to change to other values |
12 | AC Power Type | Refers to whether or not your switch needs to be changed to a neutral or non-neutral setup | Range: 0-1 0 = Single Pole 1 = Multi-Way (Dumb) Max Taps = 2
Tap down to select 0 and up to select 1 |
13 | Switch Type | Refers to the type of wiring installation your switch is in: Single Pole, 3-Way Dumb, or 3-Way Aux | Range: 0-2 0 = Single Pole 1 = Multi-Way (Dumb) 2 = Multi-Way (Aux) Max Taps = 3
Tap down to select 0 and up/down to select 1-2 |