The White Series 2-1 Switch has many different button combinations that indicate what the switch is doing or what settings and parameters are being changed.

Standard Button Combinations are used to check Thread network strength, or factory reset your switch

Quick Tap Sequences is a quick and easy way to change the important parameters (ie: changing from On/Off to Dimmer, Leading to Trailing Edge, etc).

Local Configuration is a more complex way of changing additional parameters outside of the Quick Tap Sequences.

Standard Button Combinations for your White Series 2-1 Switch are used to either check Thread network strength, or factory reset your switch.

To see the table, click here: Standard Button Combination Table

To check the strength of your Thread network where your White Series 2-1 switch is at, hold down on the configuration (favorites) button for 5-10 seconds until the LED Bar turns green. Release the configuration button when the LED Bar turns green and the color of the LED Bar will be the strength of your network: green equals good, yellow equals ok, and red equals poor.

To factory reset your White Series 2-1 switch, hold down on the top of the paddle (on) and the config/favorites button simultaneously for 20 seconds until the LED Bar (D) turns green, yellow, then red. It will blink cyan, green(non-neutral) or yellow (neutral), and then blue confirms the switch has been reset.

The White Series 2-1 Switch has various settings and parameters you can change at the switch itself via the configuration (favorites) button located at the top right of the switch.

To see the Quick Tap Sequences Table, click here: Quick Tap Sequences Table

Example: If you'd like to change your White Series 2-1 switch from an on/off switch to a dimmer switch manually, you would hold down on the bottom part of the paddle (off) while simultaneously tapping the configuration button three times (do not let go of the paddle when finished tapping the config button). Wait for the LED Bar to flash solid orange (and then let go of the paddle) indicating the switch has changed to a Dimmer switch.

To put your White Series 2-1 Switch in On/Off Mode, hold down on the top part of the paddle (on) while simultaneously tapping the configuration button three (3) times (do not let go of the paddle when finished tapping the config button). Wait for the LED Bar to flash solid red (and then let go of the paddle) indicating the switch has changed to an On/Off switch.

To put your White Series 2-1 Switch in Dimmer Mode, hold down on the bottom part of the paddle (off) while simultaneously tapping the configuration button three (3) times (do not let go of the paddle when finished tapping the config button). Wait for the LED Bar to flash solid orange (and then let go of the paddle) indicating the switch has changed to a Dimmer switch.

To enable Full Sine Mode (use if your bulbs are not fully turning on/off) on your White Series 2-1 Switch, hold down on the bottom part of the paddle (off) while simultaneously tapping the configuration button six (6) times (do not let go of the paddle when finished tapping the config button). Wait for the LED Bar to flash solid green (and then let go of the paddle) indicating the switch has enabled Full Sine On/Off Mode.

NOTE: This will only work if you have a neutral wire and the switch is wired in single-pole mode.

To enable Smart Bulb Mode on your White Series 2-1 Switch, hold down on the top part of the paddle (on) while simultaneously tapping the configuration button four (4) times (do not let go of the paddle when finished tapping the config button). Wait for the LED Bar to flash solid yellow (and then let go of the paddle) indicating the switch has enabled Smart Bulb Mode.

To disable Smart Bulb Mode on your White Series 2-1 Switch, hold down on the bottom part of the paddle (off) while simultaneously tapping the configuration button four (4) times (do not let go of the paddle when finished tapping the config button). Wait for the LED Bar to flash solid blue (and then let go of the paddle) indicating the switch has disabled Smart Bulb Mode.

To have your White Series 2-1 Switch work with an Auxiliary (Add-On) switch in a multi-way (3-Way) setting, hold down on the top part of the paddle (on) while simultaneously tapping the configuration button five (5) times (do not let go of the paddle when finished tapping the config button). Wait for the LED Bar to flash solid white (and then let go of the paddle) indicating the switch has enabled 3-Way + Aux Switch Mode.

To have your White Series 2-1 Switch work with your existing, "dumb" switch in a multi-way (3-Way) setting, hold down on the bottom part of the paddle (off) while simultaneously tapping the configuration button five (5) times (do not let go of the paddle when finished tapping the config button). Wait for the LED Bar to flash solid violet (and then let go of the paddle) indicating the switch has enabled 3-Way + Dumb Switch Mode.

To have your White Series 2-1 Switch work as a Single-Pole switch, hold down on the top part of the paddle (on) while simultaneously tapping the configuration button six (6) times (do not let go of the paddle when finished tapping the config button). Wait for the LED Bar to flash solid cyan (and then let go of the paddle) indicating the switch has enabled Single-Pole Mode.

To disable the button delay and create an, "Instant On" setup (ie: when you tap the switch, the light immediately turns on or off) on your White Series 2-1 Switch, hold down on the top part of the paddle (on) while simultaneously tapping the configuration button seven (7) times (do not let go of the paddle when finished tapping the config button). Wait for the LED Bar to flash solid green (and then let go of the paddle) indicating the switch has enabled Instant On Mode. Remember, if you enable this feature, you will no longer have multi-tap scene control from the paddle (you will still have it at the config/favorites button).

To enable the button delay and allow a 500 millisecond delay between the time you tap the switch to when the light turns on or off on your White Series 2-1 Switch, hold down on the bottom part of the paddle (off) while simultaneously tapping the configuration button seven (7) times (do not let go of the paddle when finished tapping the config button). Wait for the LED Bar to flash solid yellow (and then let go of the paddle) indicating the switch has enabled the Button Delay Mode. Remember that when there is a 500ms delay enabled, you will have the ability to create multi-tap scene control automations.

To enable the audible relay click sound (Parameter 261) on your White Series 2-1 Switch, hold down on the top part of the paddle (on) while simultaneously tapping the configuration button eight (8) times (do not let go of the paddle when finished tapping the config button). Wait for the LED Bar to flash solid cyan (and then let go of the paddle) indicating the switch has enabled the audible relay click sound.

To disable the audible relay click sound (Parameter 261) on your White Series 2-1 Switch, hold down on the bottom part of the paddle (off) while simultaneously tapping the configuration button eight (8) times (do not let go of the paddle when finished tapping the config button). Wait for the LED Bar to flash solid pink (and then let go of the paddle) indicating the switch has disabled the audible relay click sound.

To check the firmware version on your White Series Fan Switch, hold down on the down on the bottom part of the paddle (off) while simultaneously tapping the configuration button nine (9) times (do not let go of the paddle when finished tapping the config button). The LED Bar will flash white and orange in a sequence that aligns with the firmware version. For example, if the firmware version is 2.15, the switch will light up in the following way:

To enable Local Protection Mode (Parameter 256) on your White Series 2-1 Switch, hold down on the top part of the paddle (on) while simultaneously tapping the configuration button ten (10) times (do not let go of the paddle when finished tapping the config button). Wait for the LED Bar to flash solid green (and then let go of the paddle) indicating the switch has enabled Local Protection Mode.

To disable Local Protection Mode (Parameter 256) on your White Series 2-1 Switch, hold down on the bottom part of the paddle (off) while simultaneously tapping the configuration button ten (10) times (do not let go of the paddle when finished tapping the config button). Wait for the LED Bar to flash solid red (and then let go of the paddle) indicating the switch has disabled Local Protection Mode.

To put your switch into Leading Edge Mode (for dimming) on your White Series 2-1 Switch, hold down on the top part of the paddle (on) while simultaneously tapping the configuration button thirteen (13) times (do not let go of the paddle when finished tapping the config button). Wait for the LED Bar to flash solid pink (and then let go of the paddle) indicating the switch has enabled Leading Edge Mode. Please note switching between Leading Edge & Trailing Edge Mode is only available on firmware version 2.15 and above.

To put your switch into Trailing Edge Mode (for dimming) on your White Series 2-1 Switch, hold down on the bottom part of the paddle (off) while simultaneously tapping the configuration button thirteen (13) times (do not let go of the paddle when finished tapping the config button). Wait for the LED Bar to flash solid indigo (and then let go of the paddle) indicating the switch has enabled Trailing Edge Mode. Please note switching between Leading Edge & Trailing Edge Mode is only available on firmware version 2.15 and above.

To access additional parameters outside of the Quick Tap Sequences, you'll want to use Local Configuration.

To see the Local Configuration Table, click here: Local Configuration Table

Here is the logic to change the parameters locally:

Example: If you'd like to change the color of your White Series 2-1 switch LED Bar you would hold down on the configuration button until the LED Bar turns Yellow and let go. The LED Bar will blink Yellow 1x to indicate it's in Local Configuration Mode. Using the Local Configuration Table, you will see that to access the LED Bar Color, you would tap the configuration button 9x. After you tap the configuration button 9x, the LED Bar will slow blink 9x to indicate it's on the correct parameter. Next, you will tap the paddle up or down to select the LED Bar color you want. Finally, to save the configuration, you will hold down on the configuration button until the LED Bar turns Yellow and let go. It will blink Cyan to confirm.

Below you'll find tables for the Standard Button Combinations, Quick Tap Sequences as well as Local Control Options.

In order to conserve space, we've abbreviated some of the words in the, "Action" column. Here are the abbreviations:

Here's how you read this chart:

Example: If you'd like to enable Smart Bulb Mode on your White Series 2-1 switch manually, you would hold down on the top part of the paddle (on) while simultaneously tapping the configuration button four times. After the fourth time tapping, continue to hold the top part of the paddle (on) until the LED Bar flashes solid yellow indicating the switch has enabled Smart Bulb Mode.

Here's how you read this chart:

Example: Let's say you wanted to change the LED Bar to a color of orange when the load is on. You would see that the #9 is, "LED Indicator Color (When On)". Then the Value column says that Orange is an option and the instructions say to tap up/down the paddle until you find Orange. An example is shown below in the, "Video Demonstration".