This is the digital manual for the Gen 1 Dimmer Smart Plug w/Scenes.

Please click on any of the sections in the Table of Contents to get started. We recommend working your way down as it follows an intentional flow that is user friendly and hub/gateway specific. As always, any questions, please see the Additional Resources links section or submit a ticket, we’re happy to help.
​

Make sure to unplug the smart plug first prior to putting your hub into pairing mode. Once pairing mode is initiated on your hub, plug in your smart plug and it will auto-include to the hub (please note that you have 30 seconds before auto-inclusion times out). If auto-inclusion does not work (or times out), you can tap on the on/off button (A) five (5) times within a couple seconds.

Please refer to the above diagram to get to know your plug.

A. On/Off Button: Turns on and off smart outlet (C). In addition, it can be used to activate scene control (multi-tap) where up to 1 scene can be added*. Finally, it can be used for quick tap programming

B. Always-On: Pass-though, non-remote controlled outlet
​

C. Smart Outlet: Remote (Z-Wave) controlled outlet

The Inovelli smart plug can be used on various hub platforms such as: SmartThings, Home Assistant - Z-WaveJS, Home Assistant - Z-WaveJSUI, Hubitat, and HomeSeer. If you'd like specific instructions on how to setup this plug on your hub's platform, please click the links below to be taken to them:

If you don't see your hub listed above, please go to the, "Quick Setup & Inclusion" section for generic instructions.

The advanced features shown below are what is built into the plug firmware, and may or may not be supported by your hub/ gateway. We’ve confirmed they’re supported on SmartThings, Hubitat, and Home Assistant (ZHA and Z-Wave2MQTT).

Scene control allows you to multi-tap your plug to activate certain scenes. Some common examples are:

Setup instructions are different for each hub, so we've created instructions for the following hubs:

To see the list of parameters on this plug, please click on the following link: Gen 1 Smart Plug (1-Channel) Parameters

Please see the below sections to learn more about Z-Wave and how it relates to this plug.

Group 1: Lifeline

Members of this group will receive unsolicited messages related to the status of the plug.

This product can be operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. Each module is designed to act as a repeater, which will re-transmit a radio frequency (RF) signal by routing the signal around obstacles and radio dead spots to ensure that the signal is received at its intended destination. The Inovelli Dimmer Smart Plug is a security enabled Z-Wave Plus™ device. A security enabled Z-Wave Plus controller must be used in order to fully utilize the product.

To factory reset your device use a certified Z-Wave controller to remove the device from your network to factory default. Only use these procedures in the event that the primary controller is missing or otherwise inoperable.

Exclusion will reset your device as well and can be done directly from the hub. This is helpful if you’re running into issues with inclusion. To exclude a device, start the exclusion process on your hub and tap the on/off button five (5) times within two (2) seconds.

Name: Dimmer Smart Plug

SKU #: NZW39

Power: 120V AC, 60Hz Signal

(Frequency): 908.42 MHz

Operating Temperature Range: 32-104° F (0-40° C)

Maximum Load (Watts): 500W

Range: Up to 100 meters line of sight between the Wireless Controller (HUB) and the closest Z-Wave Repeater.

Certifications: UL Listed, FCC/IC & Z-Wave Plus Certified

For indoor use. Specifications subject to change without notice due to continuing product improvement.

While most Z-Wave enabled hubs are compatible with the Dimmer Smart Plug, the hubs below have been tested and verified to work. If you do not see your hub listed, please reach out prior to purchase.

*Limited functionality

If you run into any issues, feel free to reach out to us. We typically answer tickets within 24-48 hours and are staffed by actual smart home owners.

All Inovelli products come with a one (1) year warranty (defined as 365 days). This warranty protects you from breakdowns in the material or workmanship under normal use. This warranty is limited in a couple areas. Purchases must be made from Inovelli or an authorized reseller. The product should be used in the manner directed in the instructions. The product must only be used and/or installed in the United States or Canada.

For full warranty info, please visit: inov.li/warranty

(Keep in mind this may be out of date)