DISCLAIMER: You may notice there are a lot of over-used keywords or phrases as well as English that seems a little off. This is because these articles are used to feed our AI Robot (Ira) and she needs the data to be structured in a certain way.
IMPORTANT: Before installing your fan/light switch, please ensure the fan motor is set to high speed. If you notice that after you install your fan/light switch the speeds are not as fast as they were prior to installing your switch, it's likely that the motor was not on high (please adjust if you find this is the case).
This is the digital setup instructions for the Red Series Smart Fan/Light Switch on the SmartThings platform.
Navigating the Instructions
Please click on any of the sections in the Table of Contents to get started. We recommend working your way down as it follows an intentional flow that is user friendly and hub/gateway specific. As always, any questions, please see the Additional Resources links section or submit a ticket, we’re happy to help.
Quick Setup Instructions
Follow these if you have already installed the Fan/Light switch before and are just looking for some quick pairing instructions. If this is your first time installing the Fan/Light switch, please skip this section and work your way through the various sections below starting with the Prerequisites.
This section assumes the following:
You’ve installed the Edge Driver
You’ve wired the switch and it works manually
Let’s begin:
Make sure your switch LED is pulsing blue – if it’s not, press the config/favorite button three (3) times
With your LED pulsing blue, open up your SmartThings App to the, “Devices” tab and click on the + at the top right
Click, “Add Device”
Then under, “Scan for nearby devices” click, “Scan”
Hold down on the top of the light rocker and then tap the light paddle three times consecutively as shown in the GIF below
SmartThings should then search for, find and initialize the switch
Video Demonstration
Video Demonstration
If your LED bar refuses to pulse blue, you may have to factory reset your device by holding down on the top of the light rocker (A) and the light paddle (B) for 20 seconds until the LED Bars turns red and let go. The switch should blink red a few times followed by a reboot sequence indicating it has been factory reset as shown below in the GIF.
Video Demonstration
Video Demonstration
NOTE: Video shortened to reduce file size
Prerequisites
The only prerequisite to pairing this switch is the following:
Installation of the Device Edge Driver
While this switch will also pair without it, for full functionality, you’ll want to install the Edge Driver.
Device Edge Driver Installation
To install the Edge Driver, please follow the instructions below:
Click on the following link Samsung Edge Driver Access and sign into your Samsung account (you may have 2-Factor Authentication on – if so, please follow the directions Samsung gives you to attain a code)
Next, click, “Enroll” by the hub your devices are paired to
Next, click, “Available Drivers”
Finally, click on the driver you’d like installed by clicking, “Install”
(NOTE: In this case, please install, “Inovelli Fan Plus Light Red Series”)
Now when you pair your switch, it should automatically pick up the Edge Driver. Feel free to move onto the next section of the Setup Instructions below.
Installation Instructions
Before setting up your switch within SmartThings, you will have to manually install your switch in the wall and have it powered up. In order to do that, you (or your licensed electrician) will need to follow our Wiring Instructions which can be found below:
Pairing Instructions
The below instructions assume you have installed the Edge Driver prior to pairing.
Open your SmartThings App and go to the, "Devices" tab
Press the (+) button at the top right of the screen
Click on, “Add Device”
At the bottom of the screen click on, "Scan nearby"
While your SmartThings hub is scanning, hold down on the top of the light rocker (A) and then tap the light paddle (B) three times consecutively.
SmartThings will then search for your Inovelli switch and, if successful, will let you know that the device was added (NOTE: Your LED Bar may still pulse blue until it's paired securely).
We recommend setting this up with full security options - to do this, click on, "Setup" followed by, "Secure Setup".
Scan the QR Code located on the front of your switch (bottom left) or enter in the 5 digit Z-Wave DSK also located at the bottom left of the switch
If your switch was included successfully, the LED Bar should flash green and you should see a confirmation in your SmartThings app. If you'd like to rename the switch and/or change the room it's assigned to, click on, "Edit", change either or and click, "Save" and then, "Done"
Once your switch is successfully paired, check to make sure you have basic functionality of your switch by turning it on/off.
Advanced Feature Setup
This switch is packed with features and most of them come directly from this community.
Below we will provide a link to all the parameters and show you how to change them from within SmartThings and then we'll go into some of the advanced features and explain how to set them up in SmartThings.
Parameter Explanations
You will need to install an Edge Driver prior to accessing any of these features from within the app. Instructions can be found here: Edge Driver Installation
A parameter is a setting within the switch firmware that allows you to change how the switch operates. For example, you want to change how fast your fan or lights turn on, the color of the LED bars, minimum speed or dim level and much more -- all with a few clicks within the app.
To access your parameters, please follow the steps below:
Open your SmartThings App and go to the, "Devices" tab
Find your Red Series Fan/Light Switch and click on it
Click on the three dots at the top right and select, "Settings"
From here, you can scroll down, locate and change the various parameters on the switch
For a list of the most up-to-date parameters and the firmware version they are associated with, please visit the Red Series Fan/Light Switch Parameter Page
Animated Notifications
Animated notifications are used when you want to have a visual cue on your LED bar notify you of a certain event. A few examples would be:
LED Bar pulses purple if your garage door is left open past 9pm
LED Bar chases red if your front door is unlocked
LED Bar fast blinks orange if a door is opened at night time
These notifications are accomplished by using, "Routines" within the SmartThings App.
For more information about Animated Notifications as well as some examples of how to set them up, please visit the following article: Setting Up Animated Notifications • SmartThings
Scene Control
Scene control, in this context, refers to activating a scene from your light switch via a tap sequence (ie: double-tap, triple-tap, favorites button, etc). This is not to be confused with setting up scenes in your SmartThings app, which is different.
To learn how to setup multi-tap scene control, please visit the following article: Setting Up Multi-Tap Scene Control • SmartThings
Z-Wave Associations
Z-Wave Associations is when two or more Z-Wave products communicate directly with one another without the need to communicate with a hub. There are two main benefits of utilizing Z-Wave Associations: speed & local control.
From a speed standpoint, cutting out the middle-man (hub) can save precious milliseconds or even seconds depending on your cloud and/or processing power off your hub. Whereas from a local control standpoint, if your hub goes does down and cannot communicate, your products can still talk to each other.
To setup Z-Wave Associations with your SmartThings Hub, please see this article: Setting Up Z-Wave Associations • SmartThings